Smith & Wesson has identified a condition that may exist in certain PPK and PPK/S pistols which may permit a round to be discharged without the trigger being pulled. When the manual safety is disengaged, Smith & Wesson's Product Engineering Group has determined that the possibility exists in certain firearms that lowering the hammer may cause a chambered round to fire.
This recall applies to all Walther PPK and PPK/S pistols manufactured by Smith & Wesson from March 21, 2002, until February 3, 2009. The Serial Numbers of the pistol subject to this recall are as follows:
0010BAB - 9999BAB
0000BAC - 9999BAC
0000BAD - 9999BAD
0000LTD - 0499LTD
0001PPK - 1500PPK
0000BAE - 9999BAE
0000BAF - 9999BAF
0001WLE - 0459WLE
0000BAH - 9999BAH
0000BAJ - 9999BAJ
0000BAK - 9999BAK
0026REP - 0219REP
0000BAL - 5313BAL
0000BAM - 1320BAM
STOP USING YOUR PISTOL AND RETURN IT TO SMITH & WESSON AT ONCE.
Any unintended discharge of a firearm has the potential for causing injury, and we ask that you stop using your pistol immediately.
To facilitate the repair of your pistol, please contact Smith & Wesson's customer service department to receive instructions for the return of your pistol to Smith & Wesson.
When you return your pistol to Smith & Wesson, we will replace the existing hammer block feature with a new part at no cost to you. Your firearm will be returned as quickly and efficiently as possible.
When your pistol is returned, you should note a punch dot which appears at the back of the frame. See the photograph below.
This marking is verification that the new hammer block has been installed and that your pistol is safe to handle.
To receive a UPS pre-paid billable stamp and shipping instructions to arrange for the modification of your pistol click here or contact Smith & Wesson directly at 1-800-331-0852.
PPK Hammer Block Recall - Smith & Wesson

Smith & Wesson has identified a condition that may exist in certain PPK and PPK/S pistols which may permit a round to be discharged without the trigger being pulled. When the manual safety is disengaged, Smith & Wesson's Product Engineering Group has determined that the possibility exists in certain firearms that lowering the hammer may cause a chambered round to fire.
This recall applies to all Walther PPK and PPK/S pistols manufactured by Smith & Wesson from March 21, 2002, until February 3, 2009. The Serial Numbers of the pistol subject to this recall are as follows:
0010BAB - 9999BAB
0000BAC - 9999BAC
0000BAD - 9999BAD
0000LTD - 0499LTD
0001PPK - 1500PPK
0000BAE - 9999BAE
0000BAF - 9999BAF
0001WLE - 0459WLE
0000BAH - 9999BAH
0000BAJ - 9999BAJ
0000BAK - 9999BAK
0026REP - 0219REP
0000BAL - 5313BAL
0000BAM - 1320BAM
STOP USING YOUR PISTOL AND RETURN IT TO SMITH & WESSON AT ONCE.
Any unintended discharge of a firearm has the potential for causing injury, and we ask that you stop using your pistol immediately.
To facilitate the repair of your pistol, please contact Smith & Wesson's customer service department to receive instructions for the return of your pistol to Smith & Wesson.
When you return your pistol to Smith & Wesson, we will replace the existing hammer block feature with a new part at no cost to you. Your firearm will be returned as quickly and efficiently as possible.
When your pistol is returned, you should note a punch dot which appears at the back of the frame. See the photograph below.
This marking is verification that the new hammer block has been installed and that your pistol is safe to handle.
To receive a UPS pre-paid billable stamp and shipping instructions to arrange for the modification of your pistol click here or contact Smith & Wesson directly at 1-800-331-0852.
PPK Hammer Block Recall - Smith & Wesson